Filter
The VR 30 SW is a Switched Mode DC-DC converter used to convert 24Vdc to 12Vdc for use with electronic devices that require 12Vdc. It is equipped with two cooling fans on the heatsink.
SU-2450 is an industrial Switched Mode DC to DC converter used to convert 24Vdc to 50Vdc with a maximum 10A continuous load.
LPS 1012 is a reliable switching high quality fixed output voltage power supply, suitable for use with all electronic and telecommunication devices. It is equipped with an internal cooling fan.
Supplied with 230V power cable.
SPS 1050 S is a Switching power supply with variable output voltage, of high quality and reliability, suitable for use with all electronic and telecommunication devices. It is equipped with two illuminated meters (Voltmeter and Ammeter), a knob for regulating the output voltage and an internal cooling fan. The SPS 1050 S can be switched between a fixed output voltage of 13.5 V or an adjustable voltage of 9 to 15 Volt via a practical slide switch located on the front panel. SPS 1050 S is available in 110Vac and 230Vac versions.
Kit for Amplifier DC Power cable, includes:
- 3 mt silicone cable red 4 mm²
- 3 mt silicone cable black 4 mm²
- n.2 ring terminal
- n.2 fork terminal
For use with the following products:
- KL 405
- KL 405 V
- MUA 50
- MUA 100
- MLA 100
- MLA 100 V
Kit for Amplifier DC Power cable, includes:
- 3 mt silicone cable red 6 mm²
- 3 mt silicone cable black 6 mm²
- n.2 ring terminal
- n.2 fork terminal
For use with the following products:
- KL 503
- KL 503 HD
- KL 505
- KL 505 V
- KL 506
- KL 805
- HLA 300 V BLACK
- HLA 305 V
- LA 250
- LA 250 V
- LA 251
Kit for Amplifier DC Power cable, includes:
- 3 mt silicone cable red 4 mm²
- 3 mt silicone cable black 4 mm²
- n.2 ring terminal
- n.2 fork terminal
- n.2 wire end cap sleeve red
- n.2 wire end cap sleeve black
For use with the following products:
- KL 703
Permits the use of the auto radio in reception together with the CB radio in both RX and TX using only the CB antenna. This is a passive device and requires no power supply.
Permits the use of the auto radio in reception together with the VHF radio in both RX and TX using only the VHF antenna. This is a passive device and requires no power supply.
27/586 is a Low Pass Filter with a cut off frequency of 30 MHz. Stop band attenuation >60dB from 60-900 MHz. It is recommended for use if you suffer from BCI or TVI interference.
The RM 35/600 is 9 pole Chebyshev Low Pass Filter that is designed to be used for effective harmonic attenuation when transmitting within the 24MHz to 30MHz band. It features low insertion loss of less than 0.15dB and a stopband attenuation of greater than 50dB at 50MHz. Installation is very simple, the filter should be inserted directly at the output of the radio / amplifier and its output connected to the antenna. In the case that an antenna matching network is required the AMU should be connected on the output side of the filter. The Filter is labelled RTX for the Input and ANT for the Output, however it is actually a bidirectional network so can be used also in the opposite orientation without a problem.
Replacement RF Transistor for the following models:
- KL 35
- KL 60
- KL 203
- KL 203 P
- KL 503
- KL 503 HD
- KL 703
Showing 25–36 of 75 results